News

Surface treatment of magnesium alloys

First. Main surface performance requirements of magnesium products

Usually used to replace the magnesium alloy of aluminum, iron or plastic, one of the principles of surface treatment is to maintain the superior performance of the material itself, and the more important point is to improve the performance of some inferior to other materials, in order to meet the performance requirements of the product, such as corrosion resistance. The main surface performance requirements of some magnesium alloy products are listed below.

1.1 Performance requirements of automobiles, motorcycles and tools

  1. general mechanical properties: hardness, strength, impact resistance, fatigue resistance, etc.
  2. Protection: corrosion resistance, chemical resistance, weather resistance and pollution prevention.
  3. adornment: color, gloss, etc.
  4. Machability: such as weldability, bonding, etc

1.2  Performance requirements of 3C class products

  1. General mechanical properties: hardness, strength, impact resistance, fatigue resistance, etc.
  2. Protection: corrosion resistance, chemical resistance, weather resistance and pollution prevention.
  3. Thermal conductivity
  4. Electrical conductivity
  5. The electromagnetic shielding property
  6. Machability: such as weldability, bonding, etc
  7. Adornment: color, gloss, etc.

Most product parts will not put forward high requirements for the full performance, usually only for part of the performance of their products, in order to reduce the technical threshold and reduce the comprehensive cost of products.

 

Second.Material surface analysis of die-cast magnesium alloy products

In order to develop a perfect surface treatment technology and process, it is necessary to fully grasp the influence of the physical and chemical characteristics of the raw material surface, and now only the influence of the surface condition of the magnesium alloy die casting on the treatment process is analyzed.

2.1 Effect of surface original loose film

In normal atmospheric environment, Mg (OH)2And MgCO3The main is not dynamic film, this film corrosion prevention performance is not good, uncomfortable cooperation for long-term protection, should be removed before treatment.

2.2 Effect of release agent attachment

In the most practical die casting method at present, the release agent sticks to the surface of the raw material during forming, and it will be involved in the interior of the raw material, which leads to the uneven chemical properties of the surface of the product and brings difficulties to the treatment work.

2.3 Effects of alloy surface segregation and thickening

During the molding process, some alloy elements will be separated and enriched on the surface of the workpiece. For example, Al and Zn of AZ 91 series will be separated and concentrated on the surface of the die casting, resulting in the chemical chemistry of the surface and the interior of the matrix, which leads to the increase of processing difficulty.

2.4 The influence of uneven molding

The concentration of residue and alloy composition is uneven, each piece is different, and each part is completely different for the same workpiece; During the forming process, the crystallization structure of each part is uneven. For example, the gate and overflow part of a dense and fine, a rough and porous, and some parts of the dense parts mixed with rough parts, which will affect the treatment process and treatment effect.

 

 

Third.Magnesium alloy surface treatment technology

The differences of different products and their application environment, as well as the parts of different parts of the same product, the surface treatment process and methods are different.

3.1 Chemical transformation membrane

Chemical conversion film is mainly for coating pretreatment, and there are many following applications:

  1. chromium system inorganic salt conversion film. Aqueous solution chemical treatment process with chromic acid and dichromic acid as the main components, the chromate composite film has good corrosion resistance, strong adhesion of coating, and has the ability of automatic repair. At present, the relevant process has been relatively mature, but its production process is unfavorable to environmental protection, and has been gradually replaced by other non-chromium system treatment processes.
  2. Non-chromium system inorganic salt conversion film. At present, phosphate and manganate series are the main, the corrosion resistance of skin film is close to the chromic film, and other performance indicators also meet the requirements. Due to the environmental protection requirements, it has gradually become the mainstream process used in the current research and production.
  3. Non-chromium system organic transformation film. Originally developed in Japan, some domestic foreign enterprises have begun to introduce and apply them in production, mainly for 3C products that require both high corrosion resistance and good electrical conductivity.

 

  1. Chemical oxide film. The conversion film obtained through various chemical oxidation methods is mainly used in the pre-coating treatment of low-end products with low requirements and the temporary protection treatment between processes. Domestic aerospace, military enterprises as early as the 60s have relatively mature processing technology.

3.2 Anodic oxide membrane

An electrochemical conversion film, thicker than the chemical conversion film, high strength, hardness, abrasion and corrosion resistance, the film layer is porous, can be used as a good substrate before coating. The sealed workpiece has better anti-corrosion performance and can be used directly as the final coating.

3.3 Microarc oxidation

Also known as surface ceramics, is the development of anodic oxidation technology, its principle is in the anode zone plasma microarc spark, make the workpiece surface (anode) local temperature rise to 2000℃, so that the anodic oxide cladding on the workpiece surface, and combined with matrix metal metallurgy, form a layer of attached tight dense ceramic oxide film (as shown in figure 2, figure 3), its wear resistance, strength, hardness, adhesion are much better than ordinary anodic oxide film.

 

 

 

 

 

 

                                    Figure 2: surface after microarc treatment                                                  Figure 3: SEM observation of oxide film   

surface after microarc treatment

3.4 Electroplating

Domestic aerospace industry as early as in the 1980s, it has been frequently distributed magnesium and magnesium alloy gold plating process specifications, and the mature gold plating technology is widely used in aerospace and military industry, but the mature electroplating process has not been developed in the folk. In Europe, Japan and Taiwan, where the magnesium alloy industry developed earlier, there are small batch trial production.

3.5 Chemical plating

Mature direct chemical nickel plating has been used in actual production. Magnesium alloy direct plating of chemical nickel, the process is much simpler than the traditional method, short process, good coating adhesion, metallic luster, hardness up to 500-680 HV, with good conductivity (impedance of 50-100 μ Ω. Cm), with excellent EMI performance. In addition, the treatment solution does not use traditional chromic acid or cyanide, in line with environmental protection requirements.

Figure 4 is a microstructure of the chemically coated nickel, and Figure 4 is a photograph of the chemically coated nickel sample, where the crystals in the microstructure are rounded. The membrane layer of chemical nickel is light golden yellow with a distinct metallic luster.

 

 

 

 

 

 

 

 

 

 

 

                     Figure 4: Microstructure of chemical nickel plating                        Figure 5: Sample of chemical nickel plating

  

3.6 Gas phase deposition

Such as forming chromium or chromium nitride coating on the surface of magnesium alloy, or forming organic coating coating, such as polyethylene polypyrrole coating.

3.7 Other methods

Such as ion beam-assisted deposition (IBAD) magnesium oxide coating, nitrogen ion injection modification, laser surface treatment, and so on.

 

Fourth、The selection of surface treatment techniques

4.1 Choose according to the product application environment

Different products, its use environment is different, the surface of the technical requirements are not the same, so the treatment process is not the same, not only to highlight its technical requirements, but also to make the lowest cost. For example, automobile and motorcycle products should highlight their wear resistance, impact resistance, strength, hardness and other requirements, when the choice of micro arc oxidation, anodic oxidation and other processes are more suitable; 3C products emphasize its conductivity, electromagnetic shielding, conductive oxidation, organic membrane method (conductivity), non-chromium membrane (conductivity) is better.

4.2 Select according to different alloy grade and composition

Different alloy labels have different chemical components and chemical characteristics. In the die casting process, the components of surface segregation and concentration are also different, so the treatment liquid formula and process conditions are different.

4.3 Select according to the cold and hot chamber die casting

The current molding process mainly includes hot room die casting method, cold room die casting method, semi-solid die casting method, etc. Each process has different crystallization structure and surface characteristics, and its treatment formula and process will be different.

4.4 Choose according to the cost and performance ratio

A product often has a variety of process methods to choose, at this time, we should pay attention to the choice of cost performance, the selected method should be satisfactory and low cost, if the cost is higher than the actual use value, it is a waste of money, low cost but the protection method is also a waste.

Fifth、Opportunities and challenges

In recent years, the continuous expansion of the application of magnesium alloy and the rapid improvement of the absolute amount of the industry are inseparable from the development of magnesium alloy corrosion and protection technology, especially the successful research and development of AZ 91 series corrosion resistance and high purity magnesium alloy. However, so far, there are only a few surface treatment processes, and most of them have not formed a stable process system, and some can not even be mass production and application, which once became a technical bottleneck, which seriously restricted the industrialization process of magnesium alloy. The reason is that the scientific research department has no proper theoretical system; the practical application of magnesium is not long, and the production unit (business community) has not summarized enough empirical data.

At present, most of the processes used are obtained by the improvement of aluminum alloy processing technology, and there are still few original technical research, and the existing problems are as follows:

  1. The corrosion mechanism and related principles have not yet formed a complete system theory.
  2. Chroization treatment with mature process and good effect contains Cr6+And cannot meet the environmental protection requirements.
  3. Anodized oxide, it is difficult to form a complete and dense protective film.
  4. It is difficult to improve the salt spray resistance of phosphoric acid and manganese acid series.
  5. Chemical nickel plating has the problems of unstable process and high cost.

Based on the development trend of the world magnesium industry and the progress of new surface technology, the future development direction of magnesium alloy surface treatment technology may be as follows:

  1. Low and no chromium ization of environmental protection chemical transformation film technology.
  2. High-quality electroplating (chemical plating) technology.
  3. Microarc oxidation (surface ceramics) technology.
  4. Magnetron-controlled sputtering surface nanochemistry technology.
  5. Laser surface alloying technology.
  6. Liquid-phase thermal isostatic pressure technique.

 

In order to meet the requirements of the industrialization of magnesium alloy, vigorously promote production, study and research, speed up the pace, in-depth development and implementation of magnesium alloy corrosion and protection technology research, developed both conforms to the technical requirements and conform to the provisions of the environmental protection with independent intellectual property rights of high and new surface treatment technology, has great practical significance and far-reaching historical significance.