News

Sheet Metal Common Materials and Structural Design of Formed Parts

Abstract:

This paper discusses the comprehensive cold processing technology of sheet metal, focusing on its categories, stamping forming methods, commonly used materials, and structural design considerations for formed parts. The significant characteristic of sheet metal parts is their uniform thickness. The stamping process, including die types and their applications, is elaborated. Additionally, the paper examines conventional sheet metal materials such as cold-rolled steel, electrolytically galvanized steel, stainless steel, and aluminum alloy, highlighting their properties and applications. Structural design guidelines for sheet metal parts, including considerations for punching, bending, and avoiding design flaws, are also provided to ensure optimal part performance and manufacturing efficiency.

 

Keywords: Sheet Metal; Stamping Forming; Cold-Rolled Steel; Electrolytically Galvanized Steel; Stainless Steel; Aluminum Alloy; Structural Design

 

I. Introduction to Sheet Metal Categories

Sheet metal refers to a comprehensive cold processing technology for thin metal plates (typically under 6mm in thickness), encompassing processes such as punching, bending, stretching, forming, riveting, and welding. A notable feature of sheet metal parts is their consistent thickness throughout the same component.

Figure 1: Sheet Metal Material

II. Stamping Forming Methods for Sheet Metal

Stamping is a forming process that applies external force to plates, strips, tubes, and profiles using presses and dies to induce plastic deformation or separation, thereby obtaining workpieces (stampings) of the desired shape and size. The dies used in stamping are called stamping dies, which can be classified into punch dies, blanking dies, bending dies, forming dies, riveting dies, etc., based on processing elements. They can also be categorized into progressive dies, compound dies, and single-stage dies based on process combinations.

 

Single-Stage Die: Completes only one operation (e.g., punching, bending, blanking) in one stroke of the press at one station.

Compound Die: Completes multiple stamping operations simultaneously at one station in one press stroke.

Progressive Die: Also known as a multi-stage die, it completes multiple operations simultaneously at different stations in one press stroke.

III. Common Sheet Metal Stamping Materials

 

Ordinary Cold-Rolled Steel Plate (SPCC): The most commonly used metal material in sheet metal processing; iron-gray in appearance, prone to scratching and rusting; generally requires surface treatment such as powder coating, painting, or electroplating.

Electrolytically Galvanized Steel Plate (SECC): Known as electrolytic steel, it is produced by galvanizing ordinary cold-rolled steel to form a zinc coating on the surface. It retains the mechanical properties and similar processability of ordinary cold-rolled steel while adding excellent corrosion resistance and decorative properties.

Stainless Steel Plate: SUS304 is one of the most widely used stainless steels, known for its corrosion resistance, heat resistance, and excellent mechanical properties. SUS301 has slightly inferior corrosion resistance but can achieve good tensile properties, hardness, and elasticity through cold working, making it suitable for springs and other applications. Stainless steel has a metallic white and is resistant to rusting, with surfaces that can be polished, matte, brushed, etc., commonly used for decorative structural components.

Aluminum Alloy Plate: Pure aluminum is too weak for structural applications; aluminum alloy plates, such as those in the 2000, 3000, and 5000 series, are used in sheet metal processing. The 2000 series is a copper-aluminum alloy known for its high hardness, used for various medium-strength parts and components. The 3000 series is a manganese-aluminum alloy with good rust prevention properties, also known as rust-proof aluminum. The 5000 series is a magnesium-aluminum alloy characterized by low density, high tensile strength, and high elongation. Aluminum alloy is lightweight and possesses good corrosion resistance, electrical conductivity, and thermal conductivity, commonly used for exterior parts, aerospace components, etc., where precision often considers material ductility and resilience.

IV. Structural Design of Conventional Sheet Metal Parts

 

Punching: Avoid external and internal sharp corners for safety reasons (to prevent injuries to operators or users) and die manufacturing challenges (difficult to process sharp corners on die blanks, prone to cracking during heat treatment, and prone to edge chipping and rapid wear during punching, reducing die lifespan).

 

 

Before                                    After

Figure 2: Sharp Corner Structure Improvement

Avoid Excessively Long Cantilevers and Narrow Slots: To prevent material waste and ensure structural integrity.

Punch Hole Size: Appropriate sizing to maintain die strength and lifespan.

Punch Hole Spacing and Edge Distance: Small punch sizes on dies result in low strength and short lifespan. Excessive cantilevers may also waste material.

Figure 3: The Recommend Edge Distance

Avoid Holes Too Close to Bending Edges or Forming Features: To prevent structural weaknesses and manufacturing difficulties.

                                                                                    

 

Figure4: The Recommend Distance From Hole to bending

             

 Before                      After

Figure 5:  Hole Too Close to Bending Structure Improvement

 

 

Avoid Excessively Small Punching Clearances or Material Interference After Sheet Metal Unfolding: To ensure smooth manufacturing and part quality.

VI. Bending of Sheet Metal Parts

 

Bending Height: Too low bending heights can lead to distortion and difficulty in achieving desired shape and dimensional accuracy. The bending height should not be less than twice the material thickness plus the bending radius.

Figure6: The Recommend Bending Height

 

 

 

Bending Radius: To ensure bending strength, the bending radius should exceed the material's minimum bending radius.

 

Before                      After

Figure 7:  Bending Radius Structure Improvement

 

Fiber Direction: Bend perpendicular to the material's fiber direction for optimal bending performance.

                           Fiber Direction           Crack                                                         Crack       

 


                                                                                                         Before                      After             The Picture of Crack  

Figure 8:  Fiber Direction Perpendicular to Bend

 

Bending: Avoid bending failures due to inability to clamp material at the bending root. Design to prevent bending interference and ensure bending strength. Methods to ensure alignment of holes on the bending side should also be considered.

 

This paper provides a comprehensive overview of sheet metal processing, materials, and structural design considerations, guiding practitioners in achieving optimal part performance and manufacturing efficiency.