News

The Application and Critical Calculation Methods of Precision Sheet Metal Technology

Abstract:
Precision sheet metal technology, as an integral component of modern manufacturing, has experienced a broad and deepening range of applications. This paper delves into the various sectors where this technology is employed, highlighting its significance and outlining the key technical aspects involved. Furthermore, it presents the essential calculation methods for determining sheet metal part unfolding lengths, underscoring their crucial role in ensuring processing accuracy and product quality.

Keywords: Precision Sheet Metal Technology, Manufacturing Applications, Automotive Industry, Electronics and Communications, Mechanical Equipment, Medical Devices, Aerospace, Public Facilities, Key Technologies, Unfolding Length Calculations.

  1. Sheet Metal Technology Application Areas

Automotive Industry:
Precision sheet metal processing holds a pivotal position in the automotive manufacturing sector, where it is utilized in the fabrication of crucial components such as body panels, chassis, and engine mounts. These parts necessitate not only high precision but also excellent durability and safety characteristics.

Electronics and Communications:
In the electronics and communications industry, precision sheet metal technology is essential for crafting enclosures, brackets, and structural elements for devices like smartphones, computers, and routers. The stringent demands for dimensional accuracy and aesthetic quality are meticulously fulfilled through this technology.

Mechanical Equipment:
The mechanical equipment sector also relies heavily on precision sheet metal techniques for producing device housings, shrouds, brackets, and various mechanical components. The precision and strength of these parts directly impact the overall performance and reliability of the equipment.

Medical Devices:
Precision sheet metal processing is frequently employed in the medical device industry for manufacturing surgical tables, medical cabinets, diagnostic equipment housings, and structural assemblies. The extreme requirements for cleanliness and precision ensure the safety and effectiveness of medical procedures.

Aerospace:
Sheet metal processing plays a crucial role in the aerospace sector, where it is used to construct aircraft and spacecraft structures and components. These parts must withstand extreme environmental conditions and rigorous mechanical demands, which precision sheet metal technology adeptly fulfills.

Public Facilities:
Furthermore, precision sheet metal technology finds widespread application in the public facilities sector, including the manufacture of signboards, advertisement displays, and transportation infrastructure. These installations demand not only aesthetic appeal but also robust durability and stability.

  1. Key Technologies

Precision sheet metal technology encompasses several critical processes, including raw material preparation, cutting, stamping, bending, welding, polishing, and surface treatment. Notably, numerical control (NC) machining, laser cutting, and automated welding technologies are instrumental in achieving high-precision processing. These advancements not only enhance production efficiency but also significantly elevate the quality and precision of the final products.

  1. Calculation Methods for Sheet Metal Part Unfolding Lengths

In sheet metal processing, accurately calculating the unfolding length of sheet metal parts is crucial. Commonly employed methods include:

  1.  Basic Principles of Unfolded Length Calculation for Sheet Metal Parts

1.1 Definition of Unfolded Length
The unfolded length refers to the total material length required after a sheet metal part is expanded from its three-dimensional shape to a two-dimensional plane. This length directly determines the material requirements, cutting paths, and subsequent processing procedures during mold design.

1.2 Neutral Layer and K-Factor
During the bending process, the inner layer of the sheet metal part is compressed, while the outer layer is stretched. Between these two layers, there exists a neutral layer that neither compresses nor stretches. The position of the neutral layer is crucial for calculating the unfolded length. The K-factor (neutral layer coefficient) describes the position of the neutral layer relative to the material thickness and is an important parameter in the unfolded length calculation.

2. Unfolding Principles
In the bending process, the outer layer of the sheet metal is subjected to tensile stress, while the inner layer is subjected to compressive stress. Between these two layers, there exists a neutral layer that neither experiences tension nor compression. The length of the neutral layer remains unchanged during bending, making it the benchmark for calculating the unfolded length of bending parts.

The position of the neutral layer is related to the degree of deformation. When the bending radius is large and the bending angle is small, the deformation is minor, and the neutral layer is close to the center of the sheet thickness. Conversely, as the bending radius decreases and the bending angle increases, the deformation increases, and the position of the neutral layer gradually shifts towards the inside of the bending center.

3. General Bending 1 (R=0, θ=90°)

When 0 < T ≤ 0.3, L = 0

For ferrous materials (e.g., GI, SGCC, SECC, CRS, SPTE, SUS):

  • When 0.3 < T < 1.5, L = 0.4T
  • When 1.5 ≤ T < 2.5, L = 0.35T
  • When T ≥ 2.5, L = 0.3T
  1. For other non-ferrous metals (e.g., Al, Cu):

When T > 0.3, L = 0.4T

IV. General Bending 2 (R ≠ 0, θ=90°)
When using a bending punch:

  1. When R ≤ 2.0, treat as R = 0.

L' = L + 2R (where L is the value for R = 0)

  1. When R > 2.0, proceed with the original values.

When T < 1.5, L = π(R + 0.5T)/2

When T ≥ 1.5, L = π(R + 0.4T)/2

V. General Bending 3 (R=0, θ ≠ 90°)

  1. When T ≤ 0.3, L' = 0
  2. When T > 0.3, L' = (θ / 90) * L

Note: L is the compensation for θ = 90°.

VI. General Bending 4 (R ≠ 0, θ ≠ 90°)
When using a bending punch:

  1. When R < 2.0, treat as R = 0.

L' = (θ / 90) * L + 2RTAN(θ/2)

Note: L is the compensation for θ = 90°.

  1. When R > 2.0, proceed with the original values.

When T < 1.5, L' = θπ(R + 0.5*T)/180

When T ≥ 1.5, L' = θπ(R + 0.4T)/180

VII. Z-Fold 1 (Straight Edge Step Difference)

Sample production unfolding method:

  1. When H ≥ 5T, form in two stages, each calculated as a 90° bend.
  2. When H < 5T, form in one stage:

If R = 0, L' = L

If R ≠ 0 and only one internal angle is non-zero, L' = L + 2R

If R ≠ 0 and both internal angles are non-zero, L' = L + 4R

Note: L values are determined according to parameters in Appendix 1.

VIII. Z-Fold 2 (Non-Parallel Straight Edge Step Difference)
The unfolding method is the same as for parallel straight edge Z-folds (as above). Height H values are determined as shown in the illustration.

IX. Z-Fold 3 (Oblique Edge Step Difference)

  1. When H < 2T

If θ ≤ 70°, calculate as Z-Fold 1 (Straight Edge Step Difference)

  1. (In this case, L = 0.2)

If θ > 70°, calculate fully as Z-Fold 1

  1. When H ≥ 2T, unfold as two bends (R = 0, θ ≠ 90°).

X. Z-Fold 4 (Transition Segment with Two Tangent Arcs)

  1. When H ≤ 2T and the transition segment is non-linear with two tangent arcs, draw a perpendicular at the point where the two arcs meet to ensure that the fixed edge dimension offset is managed by one material thickness. Then unfold as per Z-Fold 1 (Straight Edge Step Difference).
  2. When H > 2T, evaluate product functionality before proceeding.

XI. Reverse Bending and Flattening
L = 1.6T

  1. When flattening, consider whether to score before bending based on actual conditions. The scoring position should be in the middle of the bending deformation zone.
  2. Reverse bending and flattening are typically performed in two steps:

First, V-bend at 30°, then reverse bend and flatten.

Therefore, when drawing the bending line for the unfolded diagram, it should be drawn as a 30° bend line.

XII. N-Fold

  1. When the N-fold processing method involves pad reverse bending and flattening, L values are determined according to parameters in Appendix 1.
  2. When the N-fold is processed in other ways, refer to "General Bending 4 (R ≠ 0, θ ≠ 90°)" for the unfolding algorithm.

If the bending area is a straight edge (H segment), calculate as two bends: L' = 2L (where L is the width of the 90° bending deformation zone)